Agenda

Webinar instructions will be emailed before the date of the webinar.

Please log into the webinar 15 – 30 minutes before start time.

Day One: Thursday, August 18, 2022
11:00 am – 2:15 pm CDT (including a 15-min. break)
Day Two: Friday, August 19, 2022
11:00 am – 2:15 pm CDT (including a 15-min. break)

 

Presented by
George Walters III, PE, CPD

Agenda Day One
Introduction to Pumps: Operations, Principles and Calculations
Operation of centrifugal pumps
• Intro, terms, definitions
• Centrifugal pump construction, components, impeller, motor, volute
• Incompressible fluid, pumping equations
• Closed system, open system, parallel and series pumping applications
Reviewing hydraulic principles and calculations
• Fixture units and GPM
• Friction losses/allowable pressure drop
• Static pressure vs. dynamic pressure
• Equivalent lengths

Design Standards and Codes
IPC – International Plumbing Code – state amendments NFPA
UFC – Unified Facilities Criteria (military requirements)
WBDG – Whole Building Design Guide
AHJ – Authority Having Jurisdiction
The interpreter of the Code, Plumbing Inspector, Fire Marshall
LEED – Leadership in Energy and Environmental Design
USGBC

 

Agenda Day Two
Piping System Components, Materials and Calculations
Piping system components and materials
• Copper vs. plastics, galvanized steel and stainless steel
– When, where, why
• BFP, PRV, meters
• Valves, ball valves, gate valves, butterfly valves, flow balancing valves
Making basic system calculations
• Pipe sizing
• Friction loss calculation
• Pump sizing

Handling Pump and Piping System Problems
Booster pumps
Circulating pumps, chilled water, hydronic heating, domestic hot water
Fire pumps

  

Webinar Instructions

Each webinar session earns continuing education credit and can be registered for individually. All attendees must log-on through their own email – attendees may not watch together if they wish to earn continuing education credit. HalfMoon Education Inc. must be able to prove attendance if either the attendee or HalfMoon Education Inc. is audited.

Certificates of completion can be downloaded in PDF form upon passing a short quiz. A link to the quiz will be sent to each qualifying attendee immediately after the webinar. The certificate can be downloaded from the Results page of the quiz upon scoring 80% or higher.

Webinars are presented via GoToWebinar, an easy-to-use application that can be run on most systems and tablets. Instructions and login information will be provided in an email sent close to the date of the webinar. It is highly recommended that you download, install and test the application before the webinar begins by clicking on the link in the email.

GoToWebinar App requirements:
Windows 7 – 10 or Mac OSX Mavericks (10.9) – macOS Catalina (10.15)

Web Browser:
The two most recent version of the following browsers:
Google Chrome, Mozilla Firefox, Apple Safari, Microsoft Edge
Internet Explorer v11 (or later) with Flash enabled

Internet connection: Minimum of 1Mbps       Hardware: 2GB RAM or more

For more information, visit the Support section at www.gotowebinar.com

Credits

Professional Engineers
6.0 PDHs

Architects
6.0 HSW CE Hours
6.0 AIA LU|HSW

International Code Council
.6 CEUs (Building)

 

Continuing Education Credit Information
This webinar is open to the public and is intended to offer 6.0 PDHs to professional engineers and 6.0 HSW continuing education hours to licensed architects in all states.

HalfMoon Education is an approved continuing education sponsor for engineers in Florida (Provider No. 0004647), Indiana (License No. CE21700059), Maryland, New Jersey (Approval No. 24GP00000700) and North Carolina (S-0130). HalfMoon Education is deemed an approved continuing education sponsor for New York engineers and architects via its registration with the American Institute of Architects Continuing Education System (Regulations of the Commissioner §68.14(i)(2) and §69.6(i)(2)). Other states do not preapprove continuing education providers or courses.

The American Institute of Architects Continuing Education System has approved this course for 6.0 LU|HSW (Sponsor No. J885). Only full participation is reportable to the AIA/CES.

The International Code Council has approved this event for .6 CEUs in the specialty area of Building (Preferred Provider No. 1232).

Attendance will be monitored, and attendance certificates will be available after the webinar for those who attend the entire course and score a minimum 80% on the quiz that follows the course (multiple attempts allowed).

Speakers

George Walters III. PE. CPD

Mechanical Engineer at BMH Engineering LLC
Mr. Walters is a professional engineer and is certified in plumbing design through the American Society of Plumbing Engineers. His responsibilities overlap into the professional engineering areas of civil engineering, mechanical engineering, chemical engineering, fire protection engineering, and process engineering. He performs calculations, sizes equipment, and prepares plumbing design and construction documents. Mr. Walters is a member of the Atlanta Chapter of the American Society of Plumbing Engineers (ASPE). He earned his B.S. degree in Mechanical Engineering from Georgia Tech.

AIA Info

AIA Provider Statement:

HalfMoon Education Inc. is a registered provider of AIA-approved continuing education under Provider Number J885. All registered AIA/CES Providers must comply with the AIA Standards for Continuing Education Programs. Any questions or concerns about this provider of learning program may be sent to AIA/CES (cesupport@aia.org or (800) AIA 3837, Option 3).

This learning program is registered with AIA/CES for continuing professional education. As such, it does not include content that may be deemed or construed to be an approval or endorsement by the AIA of any material of construction or any method or manner of handling, using, distributing, or dealing in any material or product.

AIA continuing education credit has been reviewed and approved by AIA/CES. Learners must complete the entire learning program to receive continuing education credit. AIA continuing education Learning Units earned upon completion of this course will be reported to AIA/CES for AIA members. Certificates of Completion for both AIA members and non-AIA members are available upon request.

Course Title: Pumping and Piping Systems

Delivery Method: Live Online

Course Description: This course examines applications for various pumping and piping systems and components in the built environment. Topics include pump construction and applications, hydraulic principles and calculations, design standards and codes, piping system components and materials, and pump and piping system troubleshooting.

Learning Objectives:

Learning Objective 1:
Learners will be able to explain how centrifugal pumps are used in closed systems, open systems, series and parallel pumping applications.

Learning Objective 2:
Learners will be able to identify key design standards and codes including the IPC, NFPA and the USGBC.

Learning Objective 3:
Learners will be able to distinguish when and where to use copper vs. plastic piping system components.

Learning Objective 4:
Learners will be able to perform basic system calculations related to pipe sizing, friction loss, and pump sizing.

Learning Objective 5:
Learners will be able to recognize pump and piping system problems and know how to handle them.

LUs: 6.0                                                                                              LU Type: LU|HSWs.

Prerequisites: Basic familiarity with pump system applications

Advance Preparation: None

Program Level: Intermediate

Course Expiration Date: 11/11/2024

Complaint Resolution Policy:

Complaints regarding this course can be emailed to fchapman@halfmoonseminars.org or by calling (715) 835-5900. A HalfMoon Education representative will respond within 72 hours to resolve the complaint, which will include, but not limited to, access to another CE activity at no or reduced cost or a full or partial refund. Each instance will be resolved on a case-by-case situation